Termékek kávézó berendezési elemek (284)

Product Features: • Used as a small 24 volt transformer for relay, pilot lights or low voltage, low power control use. • 60 Hz. operation. • Chassis mount. • With 10" leads. • CSA certified (209651). • UL listed (File #E207860).

Product Features: • High saturation flux density ferrite rods. • 1" long leads, tinned to within 1/8" of body. • Ideal for filtering or energy storage inductors. • Inductance measured at @ 1 Khz. with 0 amps. D.C. current, typical inductance change is less than 5% @ twice rated current. • Ambient temperature range -60C to +85C.

Product Features: • Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. • Sealed case and wax potted core internally for stable characteristics and long life. • Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, amy be down 1 db @ 20 Khz.). • Insertion loss of apx. 1 db. • Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance. • Distortion is apx. 1.5% @ 20 Hz. under full power. • Electrostatic shield between pri. and sec. connected to the green lead. • Humbucking construction. • Balanced split windings on pri. and sec. for circuit versatility. Primary may be used as a secondary and vice vera for impedance matching. • Includes mounting hardware. • Lead length: Min. 4". • Shipping weight 0.4 lb. (0.18 kg).

Product Features: • A perfect match to the 1650P Series Potted Output transformers. • Enclosed in a drawn steel case, the transformer is completely potted in epoxy. • Mounting hardware included. • Primary: Universal - 100, 110, 120, 200, 220, 240 VAC 50/60 Hz. • Bias Tap: 50 VAC tap from high voltage secondary C.T. • Highpot tested: 2,000 VAC. • Faraday Copper Primary Shield: The electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell). • Windings: Concentric wound for low stray field and low noise. • Finish: Black powder paint to match the 1650P Series of potted output transformers. • Units can be run full wave bridge or full wave C.T. • c UL us recognized (E207860).

Radwell will beat any like for like Automation and Electronic Control Equipment Repair quote by 10%

Product Features: • Enclosed, 4-hole mount chokes (some models also available epoxy potted in a black powder paint - drawn steel housing. Potted models mount with 1/4" - 20 hardware (included). • Tolerance of 15% on both inductance and resistance. • Inductances measured at rated D.C. current. • Minimum 8" long leads. • Units will exhibit less inductance at slightly higher currents or more at lower currents. • Perfect for high voltage power supply filtering, case matches power transformers and tube audio output transformers. • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation. • Operating temperature range is -40C to 85C. • Proper Henry testing requires an LCR meter in junction with a 25A power supply that does allow for DC bias as well a higher applied AC drive voltage to meet the test specifications.

Product Features: • Rugged black epoxy potted case with 9 pin connections (.025" square by 0.5" long). • Frequency response minimum @ 0 dbm +/- 1 db max. (+/- 0.5 db is typical) of 30 Hz. to 30 Khz., except 560Q which is 30 Hz. to 15 Khz. • Higher signal levels possible with reduced low frequency performance. • Insert loss of 1 db maximum. • Electrostatic shield between primary and secondary connected to core and brought out to pin "SH". • Humbucking construction. • Balanced split windings on pri. and sec. for circuit versatility. • Primaries and secondaries can be reversed for impedance matching. • Overall dimensions 1.64" (41.7mm) x 1.33" (33.8mm) x 0.85" (21.6mm) high max. • Shipping weight 4 oz. (0.1 kg).

Product Features: • Large ferrite core for extended saturation point, optimum frequency range .01-2 Mhz. • 1.5" long leads (+/- 0.1"). • Test frequency 1 Mhz. • Core length 1.25". • Coil is covered with vinyl insulation shrink sleeve. • Operating temperature -55°C to +135°C.

Product Features: • Economical "open bracket" - channel mount. • Tolerance of 15% on both inductances and resistance. • Inductances measured at rated D.C. current. • Minimum 5" long leads. • Units will exhibit less inductance at slightly higher currents or more inductance at lower currents. • Perfect for high voltage power supply filtering. • Every unit is Hipot tested (100%) at 1,500 VAC. • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Product Features: • All models impregnated with a moisture and fungus resistant varnish. • Lead length of 1.5" (+/- 0.13"). • Wound for low distributed capacity by using solenoid (single coil) windings. • Includes vinyl insulation cover. • Ambient temperature range -40°C to +105°C.

Fast charging car usb with dual usb port

Given the wide range of electronics devices that require low voltage power, many applications can benefit from having SELV units installed at source, thereby eliminating the need for extensive low voltage wiring. With our units also meeting IP64 this allows them to be used in a range of situations where traditional external power supplies would not be suitable. Direct charging for all USB devices Universal Input – 100-240V AC Constant Voltage, current limited Low Standby power Continuously short circuit proof Compact design IP64 rated

To see more information on this great range of products, simply click the link above or visit https://kgaenclosures.com We have over 30,000 products from great manufacturers, including Hammond Manufacturing, Deltron Manufacturing and Hylec APL Electronics. All products are available at great low competitive prices, with world-wide shipping available.

Product Features: • Primary 115 VAC, 60 Hz. (Except 261D6 and 261GE6 which are 115/230 50/60 Hz.) and (265EES which is 120/240, 50/60 Hz). • Designed for small power or bias supplies, test equipment, preamps etc. • Models 261C6, 261D6, 261E6 and 261G6 can also be used with full wave C.T. rectifiers. • Economical, two hole, channel bracket, chassis mount. • Minimum 5" long leads. • Convenient 6.3 or 12.6 volt filament/auxiliary winding.